Export Compliance: Do not remove product labeling as required by U.S. export compliance regulations.

Shock Hazard: The following paragraphs contain important safety information you must follow when installing and operating an Optotherm electrical product. Do not operate the product in a manner not specified in the documentation. Misuse of product components may result in a hazard and may compromise the safety protection built into the product. If the product is damaged, turn it off and do not use it until service-trained personnel can check its safety. If necessary, return the product to Optotherm for repair.

Keep away from live circuits. Do not remove equipment enclosures, covers, or shields unless you are trained to do so. If signal wires are connected to the product, hazardous voltages can exist even when the equipment is turned off. To avoid a shock hazard, do not perform procedures involving enclosure, cover, or shield removal unless you are qualified to do so. Disconnect all field power prior to removing enclosures, covers, or shields.

Because of the danger of introducing additional hazards, do not install unauthorized parts or modify the product. Use the product only with the chassis, modules, accessories, and cables specified in the installation instructions. All enclosures, covers, and shields must be installed while operating the product.

Do not operate the product in an explosive atmosphere or where flammable gases or fumes may be present. Operate the product only in pollution-free environments. Pollution consists of any foreign matter (solid, liquid, or gas) that may reduce dielectric strength or surface resistivity. The unit must be completely dry and free from contaminants prior to operation.

ESD Damage: Electronic hardware sensitive to electrostatic discharge (ESD) damage are shipped in an antistatic package. To prevent damage when handling, take the following precautions:

• Before touching hardware or cables, ground yourself using a grounding strap or by touching a grounded object, such as a computer chassis.

• Before removing the hardware from antistatic packaging, touch the package to a metal part of the computer chassis.

• Remove hardware from antistatic packaging and inspect it for loose components or any other signs of damage. Notify Optotherm if the hardware appears damaged in any way.

• Avoid touching exposed pins of connectors.

• Store hardware in the antistatic package when not in use.

Copyright

This manual is copyrighted by Optotherm, Inc. with all rights reserved.  Under the copyright laws, this manual may not be reproduced in any form, in whole or in part, without the prior written consent of Optotherm, Inc.

Trademarks

Optotherm, Sentris, and Thermalyze are trademarks of Optotherm, Inc. All other product and brand names are trademarks of their respective owners.

Disclaimer

Optotherm, Inc. has reviewed this manual thoroughly in order that it will function as a manual for an Optotherm product.  All statements, technical information, and recommendations in this manual and in any guides or related documents are believed reliable, but the accuracy and completeness thereof are not guaranteed or warranted, and they are not intended to be, nor should they be understood to be, representations or warranties concerning the products described.

Specifications are subject to change without notice.

All information regarding non-Optotherm products was compiled from publicly available information.  No representation is made regarding the accuracy thereof.

 

Software Warranty

Limited Warranty

Optotherm, Inc. warrants Sentris software to be free from defects in material and workmanship for a period of one year from the date of original purchase.  Optotherm, Inc. assumes no responsibility for any special or consequential damages.

Copyright Notice

Sentris software is copyrighted.  All rights are reserved.  Sentris software may not, in whole or in part, be copied, photocopied, reproduced, translated, or reduced to any electronic medium or machine-readable form without prior consent, in writing, from Optotherm, Inc.

Disclaimer of All Warranties and Liability

Optotherm, Inc. makes no warranties, either expressed or implied except as explicitly set forth in the Limited Warranty above, with respect to this manual nor with respect to the product described in this manual, its quality, performance, merchantability, or fitness for any purpose.  Optotherm, Inc. software is sold or licensed "as is."  The entire risk as to its quality and performance is with the buyer.  Should the programs prove defective following their purchase, the buyer assumes the entire cost of all necessary servicing, repair, or correction and any incidental or consequential damages.  In no event will Optotherm, Inc. be liable for direct, indirect, incidental, or consequential damages resulting from any defect or the possibility of such damages.  Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you.

Optotherm Limited Warranty on Hardware

Optotherm, Inc. ("Optotherm") warrants its new hardware products against defects in materials and workmanship for a period of one (1) year from the date of the original purchase.  The one-year warranty period begins when the new product is received by the customer.  Optotherm warrants its remanufactured products and non-warranty repair to hardware from defects in material and workmanship for a period of ninety (90) days.  The ninety-day warranty period begins the date the repaired or remanufactured product is shipped from Optotherm.

If you discover a defect, Optotherm will, at its option, repair or replace the product at no charge provided you return it during the warranty period, with transportation charges prepaid, to the Optotherm Technical Support Department.  Please contact the Optotherm Technical Support Department by phone, fax, or Email for a Return Material Authorization number (RMA#) before returning the equipment.

This warranty applies only to hardware products: Optotherm software, media, and manuals are licensed and warranted pursuant to the Software Warranty section in this manual.

This warranty does not apply to non-rechargeable batteries.  This warranty is void if the product has been damaged by accident, abuse, misuse, product end-of-life, or misapplication; has been modified without the written permission of Optotherm; or if any Optotherm serial number has been removed or defaced.  Optotherm may use remanufactured, refurbished, or used parts and modules in making warranty repairs.

THE WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHERS, ORAL OR WRITTEN, EXPRESSED, OR IMPLIED.  No Optotherm dealer, agent, or employee is authorized to make any modification, extension, or addition to this warranty.

OPTOTHERM IS NOT RESPONSIBLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY, OR UNDER ANY LEGAL THEORY, INCLUDING LOST PROFITS, DOWNTIME, GOODWILL, DAMAGE TO OR REPLACEMENT OF EQUIPMENT AND PROPERTY, AND ANY COSTS OF RECOVERING, REPROGRAMMING, OR REPRODUCING ANY PROGRAM OR DATA STORED IN OR USED WITH OPTOTHERM PRODUCTS.

Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you.

Extended Warranties

[PN0326] Sentris Warranty, Additional 1 Year